The Dad Collection – Meyer Machine Supply & Equipment

steroids for sale fast shipping steroids for sale online anabolic steroids for sale

1-800-728-3828

Meyer Machine Supply & Equipment

Father’s Day Featured Items

Add to cart

AGR601 – Residential Button-Lock Rotary Brushing Kit
$617.00
Residential Button-Lock Rotary Brushing Kit. The Residential Button-Lock Rotary Brushing Kit provides the brushes you’ll need to tackle just about every job. The kit includes 20′ and 30′ drill driven brushing shafts and 8 brushes. Brushes selection outfits you to clean flex duct, round pipe, rectangular duct, dryer vents and more. This rotary brushing cable and system is designed to be used with a clutch enabled drill.

Add to cart
Add to cart

DSR222 – RE-500 Interior Coating/Insulation Encapsulant – Black
$195.00
RE-500, now with complete one-coat coverage, is a high-performance, spray-applied insulation encapsulant and coating for use inside HVAC ductwork. RE-500 is formulated with EPA-registered chemicals to resist microbial growth on the surface of the coating. At 13 g/l, this low VOC coating is ideal for critical projects such as hospital and schools. The semi-gloss finish provides a non-stick surface that will inhibit fiberglass degradation and debris accumulation that could lead to mold and mildew growth.

Add to cart
Add to cart

DSR232 – Smoke & Soot Post Fire Smoke Encapsulant & Odor Remover – Black
$315.00
Hardcast Smoke & Soot is a spray-applied coating that resists microbial growth, locks down offensive particles, and removes odors from the air-stream of fugitive emissions from fire deposits below the detectable limit. Designed with an EPA registered chemical package, this coating was engineered to be used on ductwork and insulation that has been exposed to smoke and soot from a fire to negate the need to replace the entire duct by merely resurfacing the existing substrate.

Add to cart
Add to cart

DSR241 – Pan-Grip Burst Bag
$46.00
Pan-Grip is a multicomponent novolac based epoxy product that is ideal for residential, commercial and industrial applications. The product is designed to seal and repair corroded and leaking drain pans and surfaces. The product can be used on horizontal and vertical surfaces. The coating is impervious to water, non-rusting, and can be applied directly to a properly cleaned and prepared condensate pan without a primer. Pan-Grip can be applied and will cure under water.

Add to cart
Add to cart

DSR243 – Pan-Grip 1 gallon kit
$293.00
Pan-Grip is a multicomponent novolac based epoxy product that is ideal for residential, commercial and industrial applications. The product is designed to seal and repair corroded and leaking drain pans and surfaces. The product can be used on horizontal and vertical surfaces. The coating is impervious to water, non-rusting, and can be applied directly to a properly cleaned and prepared condensate pan without a primer. Pan-Grip can be applied and will cure under water.

Add to cart
Add to cart

ENG142 – 5 Gallon SureCan Gas Can
$55.00
ENG142 – 5 Gallon SureCan Gas Can – This is not your same old, hard to use, spill on yourself Gas Can. SureCan is a High Quality fuel dispensing machine 100% Made in the USA! SureCan is the first of its kind and the only Gas Can available with the spout at the bottom and thumb control button on top that allows one handed use to Feed Your Machines. The flexible spout rotates down more than 180 degrees and fits perfectly into any machines fill location while the thumb release button on top controls the flow. By pulling straight back on the safety trigger and then down on the thumb button, fuel is then released immediately while you stay in complete control the entire time. As fuel reaches the top of the tank, let off the thumb button slowing the flow down so that the fill tank does not overflow. This means for you, no more bending over, tipping your fuel can forward and holding it in an awkward position! Not only is SureCan easy to use it is the most durable gas can on the market!

Add to cart
Add to cart

ENG143 – 2.2 Gallon SureCan Gas Can
$45.00
ENG143 – 2.2 Gallon SureCan Gas Can – This is not your same old, hard to use, spill on yourself Gas Can. SureCan is a High Quality fuel dispensing machine 100% Made in the USA! SureCan is the first of its kind and the only Gas Can available with the spout at the bottom and thumb control button on top that allows one handed use to Feed Your Machines. The flexible spout rotates down more than 180 degrees and fits perfectly into any machines fill location while the thumb release button on top controls the flow. By pulling straight back on the safety trigger and then down on the thumb button, fuel is then released immediately while you stay in complete control the entire time. As fuel reaches the top of the tank, let off the thumb button slowing the flow down so that the fill tank does not overflow. This means for you, no more bending over, tipping your fuel can forward and holding it in an awkward position! Not only is SureCan easy to use it is the most durable gas can on the market!

Add to cart
Add to cart

GEN200 – 20 HP General Power Vacuum.
$5,200.00
[pdf-embedder url="https://www.meyermachine.com/wp-content/uploads/2020/06/General.pdf" title="General.PDF Download"][pdf-embedder url="https://www.meyermachine.com/wp-content/uploads/2020/11/IOM_GENERAL.pdf"]

20 HP General Power Vacuum. The General is All the Vacuum You’ll Need for Duct Cleaning. Kohler Command Engine, 5,250 CFM, Portable 4-Wheel Cart.

If your Air Duct Cleaning Crew needs a vacuum collector with Serious Suction… Look No Further. The General delivers ‘Duct-Truck’ like performance at a fraction of the price and without being tied to the curb.

The General is the vacuum/collector you need for a powerful start in the air duct cleaning business. The General has the versatility to tackle residential, light commercial, and indsutrial application cleaning projects.

The General is a high powered Gas Portable Air Duct Cleaning Vacuum that features a portable four-wheeled cart for placement at the job-site in the most opportunistic spot. On many residential air duct cleaning projects, the General can be connected to the air duct system with 50′-75′ of vacuum hose, allowing for maximum airflow by the vacuum.

Excessive hose runs, and long setup times are a thing of the past when your cleaning crew operates The General. With average hose runs between 50′-75′, setup times for a two-man crew can be limited to 10 minutes; storing truck-loads of bulky hose for residential cleaning projects can be a problem of the past.

The material handling fan-wheel on The General, allows for constant airflow of 5,250 CFM through the entire cleaning process. Dirty filters in the airstream are a non-issue with The General. An oversize cloth filter bag acts as the filter device, and a large cannister collects removed debris for disposal.

As air duct cleaning projects increase in size, airflow should in turn also increase. The coupling of two General power vacuums together is an effective, low cost method for increasing airflow on projects that demand it. In light commercial and industrial applications, The General is capable of pulling through hose-runs up to 250′ in length. The General is also available with Alternate Fuel/Power Options including LP-GAS and Electric Motor. For industrial applications that allow the combustion of LP-GAS engines indoors, bring The General indoors to reduce hose runs and increase airflow. Filtration cabinets are available for LP-GAS and Electric Powered vacuum arrangements that can provide CLASS 100, HEPA filtered air.

The General Air Duct Cleaning system can be comfortably set-up in a box truck or enclosed trailer, sized 6′ x 12′ or larger. Complete cleaning packages are available for all applications including residential, light commercial, industrial, and other special arrangements. Plan your custom package with the sales team, or choose from the popular arrangments that include The General, a powerful air compressor, vacuum hose, compressed air cleaning whips, duct brushes, tools, and materials necessary to access and make proper closure to many types of ductwork.

Add to cart
Add to cart

GEN930 – OSHA/EPA Compliant 6-Gallon Fuel Cell Retro-Fit Kit for General, Ranger, and Major Power Vacuums
$348.00
OSHA/EPA Compliant 6-Gallon Fuel Cell Retro-Fit Kit for General, Ranger, and Major Power Vacuums. The bolt-on fuel cell kit comes with drill templates for retro-fit on older vacuums, new vacuums are pre-drilled and ready for installation. The kit includes a 6-gallon Flambeau tank, a heavy duty frame, the required hoses, and all the necessary hardware. Installation of this kit removes the necessity of detatchable fuel cells and any quick-disconnect fittings. Add this item to your new vacuum purchase. Carbon cannister (GEN933) not included. For CARB compliancy add P/N: GEN933 to your order.

Add to cart
Add to cart

HCT019 – Lenox/Hilmor Duct Knife.
$26.00
Lenox/Hilmor Duct Knife. Professional quality hand tools are a must on the job site. Never be without a dual sided, specially purposed Duct Knife when the job requires. Make clean cuts through duct insulation or duct board.

Add to cart
Add to cart

PAT223-16 – Hinged-PSA Access Door,16″x16″
$17.00
Hinged Access Door for Sheet Metal Duct Work. 16″ x 16″ Hinged Door is Secured with 2 Cam-Locks. Pressure Sensitive Adhesive flange for easy installation.

Add to cart
Add to cart

PAT224-12 – Cammed-PSA Access Door,12″x12″
$29.00
Cammed Access Door for Sheet Metal Duct Work. 12″ x 12″ Hinged Door is Secured with 2 Cam-Locks. Pressure Sensitive Adhesive flange for easy installation.

Add to cart
Add to cart

PPE022 – Honeywell North Full-Face Respirator – Medium/Large
$201.00
HONEYWELL NORTH FULL FACE RESPIRATOR – M/L. SCRATCH RESIST 200 DEG POLY-CARB LENS. THREADED FILTER & CARTRIDGE ATTACHMENT. FILTERS/CARTRIDGES SOLD SEPARATE

Add to cart
Add to cart

PPE025 – Honeywell VAPOR/GAS/P100 Combo-Cartridge
$47.00
HONEYWELL NORTH RESPIRATOR FILTER/CARTRIDGE COMBO. THREADS ONTO NORTH HALF/FULL FACE RESPIRATORS. ORGANIC VAPOR / ACID GAS / P100 FILTER.(SOLD AS A 2-PACK)

Add to cart
Add to cart

RDC102 – 8″ x 8″ x 10″ Y-Hose Splitter.
$254.00
8″ x 8″ x 10″ Y-Hose Splitter. Adapt your vacuum hose run from ONE 10″ diameter hose to TWO 8″ diameter hoses. Use with the General or Ranger on small duct cleaning jobs to tackle the supply and return side the HVAC System at the same time. Construction is of #16 Ga. Steel for durability and long lasting use with a gloss black powder coat finish. Use 2″ – 12″ Adjustable Hose Clamps, CLP004, to secure hose to hose collars. This fitting connects ONE 10″ diameter hose to TWO 8″ diameter hoses. Other sizes are available on Special Order.

Add to cart
Add to cart

STC208 – 8″ Floor Vent Hose Adaptor
$181.00
8″ Floor Vent Hose Adaptor. Use the 8″ Floor Vent Hose Adaptor in unconventional air duct cleaning system hook-ups. Down-Flow furnaces that run duct work through slab are hard to get to, but the 8″ Floor Vent Hose Adaptor solves the problem. 1″ access holes make for easy insertion of cleaning tools.

Add to cart
Add to cart

TAP001 – Aluminum Foil Duct Tape.
$25.00
Aluminum Foil Duct Tape. 2-1/2″ x 60 Yards. U/L 181A-P Listed. Perfect for sealing duct work openings, to the NADCA Standard, ACR2013.

Add to cart
Add to cart

TAP005 – Vent / Grill Mask Tape.
$28.00
Vent / Grill Mask Tape. 8″ x 200′ with 4″ perforation. Use this Vent / Grill Mask Tape to block registers during duct cleanings or sealant application. Blue coloring to film makes this product easy to spot at the end of the job, and light tack allows for easy removal to reduce paint chipping.

Add to cart
Add to cart

ZBG002 – 26″ diameter zone bag.
$103.00
26″ diameter zone bag. Use air filled zone bags to split large duct systems into small zones for easier cleaning when airflow is limited. Zone a system to maximize airflow with whatever vacuum you use.

Add to cart