-
DSR232 – Smoke & Soot Post Fire Smoke Encapsulant & Odor Remover – Black
$315.00Hardcast Smoke & Soot is a spray-applied coating that resists microbial growth, locks down offensive particles, and removes odors from the air-stream of fugitive emissions from fire deposits below the detectable limit. Designed with an EPA registered chemical package, this coating was engineered to be used on ductwork and insulation that has been exposed to smoke and soot from a fire to negate the need to replace the entire duct by merely resurfacing the existing substrate.
-
DSR241 – Pan-Grip Burst Bag
$46.00Pan-Grip is a multicomponent novolac based epoxy product that is ideal for residential, commercial and industrial applications. The product is designed to seal and repair corroded and leaking drain pans and surfaces. The product can be used on horizontal and vertical surfaces. The coating is impervious to water, non-rusting, and can be applied directly to a properly cleaned and prepared condensate pan without a primer. Pan-Grip can be applied and will cure under water.
-
DSR242 – Pan-Grip Cartridge
$48.00Pan-Grip is a multicomponent novolac based epoxy product that is ideal for residential, commercial and industrial applications. The product is designed to seal and repair corroded and leaking drain pans and surfaces. The product can be used on horizontal and vertical surfaces. The coating is impervious to water, non-rusting, and can be applied directly to a properly cleaned and prepared condensate pan without a primer. Pan-Grip can be applied and will cure under water.
-
DSR243 – Pan-Grip 1 gallon kit
$293.00Pan-Grip is a multicomponent novolac based epoxy product that is ideal for residential, commercial and industrial applications. The product is designed to seal and repair corroded and leaking drain pans and surfaces. The product can be used on horizontal and vertical surfaces. The coating is impervious to water, non-rusting, and can be applied directly to a properly cleaned and prepared condensate pan without a primer. Pan-Grip can be applied and will cure under water.
-
DVB105 – Plug-In SmartPhone Vane Anemometer
$88.00Plug-In SmartPhone Vane Anemometer. Use DVB105 to measure airflow velocity up to 11,000 ft/min. DVB105 features a SmartPhone APP that allows for record keeping, register dimensioning, and automatic CFM conversion. DVB105 shows airflow in FPM, CFM, CMH, MPS. Send onsite professional reports from you SmartPhone or Device by email. The DVB105 is a perfect low cost solution for measuring airflow velocities for the DEDP Testing protocol and HVAC registers. Download the APP here for ANDROID, and IOS. This device connects to SMART devices via 1/8″ mini-plug.
-
DVB106 – Wireless SmartPhone Vane Anemometer
$140.00Wireless/Bluetooth SmartPhone Vane Anemometer. Use DVB105 to measure airflow velocity up to 11,000 ft/min. DVB106 features a SmartPhone APP that allows for record keeping, register dimensioning, and automatic CFM conversion. DVB106 shows airflow in FPM, CFM, CMH, MPS. Use DVB106 to also measure Temperature, Humidity and Air Pressure. Send onsite professional reports from your SmartPhone or Device by email. The DVB106 is a perfect low cost solution for measuring airflow velocities for the DEDP Testing protocol and HVAC registers. Download the APP here for ANDROID, and IOS. This device connects to Smart Devices VIA Bluetooth.
-
ENG142 – 5 Gallon SureCan Gas Can
$55.00ENG142 – 5 Gallon SureCan Gas Can – This is not your same old, hard to use, spill on yourself Gas Can. SureCan is a High Quality fuel dispensing machine 100% Made in the USA! SureCan is the first of its kind and the only Gas Can available with the spout at the bottom and thumb control button on top that allows one handed use to Feed Your Machines. The flexible spout rotates down more than 180 degrees and fits perfectly into any machines fill location while the thumb release button on top controls the flow. By pulling straight back on the safety trigger and then down on the thumb button, fuel is then released immediately while you stay in complete control the entire time. As fuel reaches the top of the tank, let off the thumb button slowing the flow down so that the fill tank does not overflow. This means for you, no more bending over, tipping your fuel can forward and holding it in an awkward position! Not only is SureCan easy to use it is the most durable gas can on the market!
-
ENG143 – 2.2 Gallon SureCan Gas Can
$45.00ENG143 – 2.2 Gallon SureCan Gas Can – This is not your same old, hard to use, spill on yourself Gas Can. SureCan is a High Quality fuel dispensing machine 100% Made in the USA! SureCan is the first of its kind and the only Gas Can available with the spout at the bottom and thumb control button on top that allows one handed use to Feed Your Machines. The flexible spout rotates down more than 180 degrees and fits perfectly into any machines fill location while the thumb release button on top controls the flow. By pulling straight back on the safety trigger and then down on the thumb button, fuel is then released immediately while you stay in complete control the entire time. As fuel reaches the top of the tank, let off the thumb button slowing the flow down so that the fill tank does not overflow. This means for you, no more bending over, tipping your fuel can forward and holding it in an awkward position! Not only is SureCan easy to use it is the most durable gas can on the market!
-
ENG144 – SureCan 5 Gallon Replacement Spout & Fill Cap w/Tether
$10.00ENG144 – SureCan 5 Gallon Replacement Spout & Fill Cap w/Tether
-
ENG145 – SureCan 2.2 Gallon Replacement Spout & Fill Cap w/Tether
$10.00ENG145 – SureCan 2.2 Gallon Replacement Spout & Fill Cap w/Tether
-
ENG146 – SureCan Replacement Thumb Valve (2.2 Gal & 5 Gal)
$10.00ENG146 – SureCan Replacement Thumb Valve (2.2 Gal & 5 Gal)
-
ENG147 – SureCan Replacement Spout Assembly (2.2 Gal & 5 Gal)
$10.00ENG147 – SureCan Replacement Spout Assembly (2.2 Gal & 5 Gal)
-
FOG020 – The Squall
$232.00The Squall Cold Mist Fogger Attachment. The Squall is a remote venturi air/liquid mixing nozzle, specifically designed for use in air ducts and on HVAC equipment. The design allows for a cleaning technician to attach it to standard compressed air duct cleaning extension lines like the Hurricane. Using compressed air its power source, the treatment liquid is drawn through the liquid line to the mixing nozzle where it is then sprayed out in a micro-drop mist. By leveraging the use of existing compressed air extension lines, the Squall cold mist fog can be applied from within the duct, providing consistent product application as the nozzle is retracted back toward the technician. Additionally, The Squall can be used for directed or general broadcast cold mist fog outside of an air duct. Download Fogging Catalog Page.
-
GEN007 – Dust Collection Bucket and Clamp
$98.00Dust Bucket and Clamp. The General and Ranger Duct Cleaning Vacuums use this Dust Bucket and Clamp under the filter bag to collect dirt and debris. This heavy duty bucket and clamp allow for easy clean up after duct cleaning jobs. Use a trash liner to collect debris for easy removal. Bucket and Clamp are only sold together.
-
GEN200 – 20 HP General Power Vacuum.
$5,200.00[pdf-embedder url="https://www.meyermachine.com/wp-content/uploads/2020/06/General.pdf" title="General.PDF Download"][pdf-embedder url="https://www.meyermachine.com/wp-content/uploads/2020/11/IOM_GENERAL.pdf"]
20 HP General Power Vacuum. The General is All the Vacuum You’ll Need for Duct Cleaning. Kohler Command Engine, 5,250 CFM, Portable 4-Wheel Cart.
If your Air Duct Cleaning Crew needs a vacuum collector with Serious Suction… Look No Further. The General delivers ‘Duct-Truck’ like performance at a fraction of the price and without being tied to the curb.
The General is the vacuum/collector you need for a powerful start in the air duct cleaning business. The General has the versatility to tackle residential, light commercial, and indsutrial application cleaning projects.
The General is a high powered Gas Portable Air Duct Cleaning Vacuum that features a portable four-wheeled cart for placement at the job-site in the most opportunistic spot. On many residential air duct cleaning projects, the General can be connected to the air duct system with 50′-75′ of vacuum hose, allowing for maximum airflow by the vacuum.
Excessive hose runs, and long setup times are a thing of the past when your cleaning crew operates The General. With average hose runs between 50′-75′, setup times for a two-man crew can be limited to 10 minutes; storing truck-loads of bulky hose for residential cleaning projects can be a problem of the past.
The material handling fan-wheel on The General, allows for constant airflow of 5,250 CFM through the entire cleaning process. Dirty filters in the airstream are a non-issue with The General. An oversize cloth filter bag acts as the filter device, and a large cannister collects removed debris for disposal.
As air duct cleaning projects increase in size, airflow should in turn also increase. The coupling of two General power vacuums together is an effective, low cost method for increasing airflow on projects that demand it. In light commercial and industrial applications, The General is capable of pulling through hose-runs up to 250′ in length. The General is also available with Alternate Fuel/Power Options including LP-GAS and Electric Motor. For industrial applications that allow the combustion of LP-GAS engines indoors, bring The General indoors to reduce hose runs and increase airflow. Filtration cabinets are available for LP-GAS and Electric Powered vacuum arrangements that can provide CLASS 100, HEPA filtered air.
The General Air Duct Cleaning system can be comfortably set-up in a box truck or enclosed trailer, sized 6′ x 12′ or larger. Complete cleaning packages are available for all applications including residential, light commercial, industrial, and other special arrangements. Plan your custom package with the sales team, or choose from the popular arrangments that include The General, a powerful air compressor, vacuum hose, compressed air cleaning whips, duct brushes, tools, and materials necessary to access and make proper closure to many types of ductwork.
-
GEN930 – OSHA/EPA Compliant 6-Gallon Fuel Cell Retro-Fit Kit for General, Ranger, and Major Power Vacuums
$348.00OSHA/EPA Compliant 6-Gallon Fuel Cell Retro-Fit Kit for General, Ranger, and Major Power Vacuums. The bolt-on fuel cell kit comes with drill templates for retro-fit on older vacuums, new vacuums are pre-drilled and ready for installation. The kit includes a 6-gallon Flambeau tank, a heavy duty frame, the required hoses, and all the necessary hardware. Installation of this kit removes the necessity of detatchable fuel cells and any quick-disconnect fittings. Add this item to your new vacuum purchase. Carbon cannister (GEN933) not included. For CARB compliancy add P/N: GEN933 to your order.
-
GEN933 – 400cc Carbon Cannister for CARB Compliancy on 6 Gallon Fuel Cell.
$78.00400cc Carbon Cannister for CARB Compliancy on 6 Gallon Fuel Cell. Add this 400cc carbon cannister to your General, Major, or Ranger vacuum and 6 gallon fuel cell for CARB comliancy.
-
HCT013 – Lenox/Hilmor Aviation Tin Snips, LEFT
$24.00Lenox/Hilmor Aviation Tin Snips, LEFT. Professional quality hand tools are a must on the job site. Never be without a pair of snips for cutting through sheet metal when power tools are not avaiable or the job doesn’t permit.
-
HCT014 – Lenox/Hilmor Aviation Tin Snips, RIGHT
$24.00Lenox/Hilmor Aviation Tin Snips, RIGHT. Professional quality hand tools are a must on the job site. Never be without a pair of snips for cutting through sheet metal when power tools are not avaiable or the job doesn’t permit.
-
HCT015 – Lenox/Hilmor Aviation Tin Snips, STRAIGHT
$24.00Lenox/Hilmor Aviation Tin Snips, STRAIGHT. Professional quality hand tools are a must on the job site. Never be without a pair of snips for cutting through sheet metal when power tools are not avaiable or the job doesn’t permit.
-
HCT016 – Lenox/Hilmor 3-Blade Sheet Metal Crimper
$24.00Lenox/Hilmor 3-Blade Sheet Metal Crimper. Professional quality hand tools are a must on the job site. Never be without a set of crimpers when duct/pipe fitting is part of your job. Use the 3-Blade Crimpers to fit same-size sheet metal snap-lock pipe end to end with ease.
-
HCT017 – Lenox/Hilmor 3 inch Seamer
$47.00Lenox/Hilmor 3 inch Seamer. Professional quality hand tools are a must on the job site. Never be without a set of seamers when duct/pipe fitting is part of your job. Use the 3 inch Seamer to make small sheet metal bends and simple fabrications.
-
HCT018 – Lenox/Hilmor 1 inch V-Notcher
$36.00Lenox/Hilmor 1 inch V-Notcher. Professional quality hand tools are a must on the job site. Never be without a set of notchers when duct/pipe fitting is part of your job. Use the 1 inch notcher to make small sheet metal notches for simple fabrications.
-
HCT019 – Lenox/Hilmor Duct Knife.
$26.00Lenox/Hilmor Duct Knife. Professional quality hand tools are a must on the job site. Never be without a dual sided, specially purposed Duct Knife when the job requires. Make clean cuts through duct insulation or duct board.
-
HCT020 – Lenox/Hilmor 12-in-1 Fin Comb
$25.00Lenox/Hilmor 12-in-1 Fin Comb. Professional quality hand tools are a must on the job site. Never clean or maintain a cooling coil without repairing damaged fins. Use the 12-in-1 Fin Comb to straighten bent over fins, restoring coil efficiecy.
-
HCT021 – Lenox/Hilmor 1/4 & 5/16 Quick-Change Nut Driver
$26.00Lenox/Hilmor 1/4 & 5/16 Quick-Change Nut Driver. Professional quality hand tools are a must on the job site. Never be without a professional nut driving tool to remove and install the most common sized screw heads in the HVAC industry.
-
HCT022 – Lenox/Hilmor 9-in-1 Ratcheting Multi-Driver
$31.00Lenox/Hilmor 9-in-1 Ratcheting Multi-Driver. Professional quality hand tools are a must on the job site. This 9-in-1 driver tool puts the most common driver bits in the HVAC industry at your fingertips.
-
HCT024 – Lenox/Hilmor 6-in-1 Stubby Multi-Driver
$13.00Lenox/Hilmor 6-in-1 Stubby Multi-Driver. Professional quality hand tools are a must on the job site. This 6-in-1 driver tools puts some of the most common driver bits at your finger tips in a STUBBY Style driver.
-
HSW001 – 1″ Lenox Bi-Metal Hole Saw.
$16.001″ Lenox Bi-Metal Hole Saw. This tough hole saw is great for making 1″ holes in sheet metal, wood, or other fibrous materials. This hole saw comes complete with pilot bit and fits in any drill with a 3/8″ or larger chuck.
-
HSW003 – 2-1/2″ Lenox Bi-Metal Hole Saw.
$25.002-1/2″ Lenox Bi-Metal Hole Saw. This tough hole saw is great for making 2-1/2″ holes in sheet metal, wood, or other fibrous materials. This hole saw comes complete with pilot bit and fits in any drill with a 3/8″ or larger chuck.
